Get a quote

Battery and Alternator Test Calculator

Four multimeter readings tell you most of what an auto electrician needs to know: how charged the battery is, whether it holds up while cranking, and whether the alternator is charging properly. Enter what you measured and the meter interprets it.

AE-V DCAuto-range · 12/24 V
State of charge–
Battery charge
–
Cranking
–
Charging
–
Charging under load
–

Measure across the battery posts with a digital multimeter on DC volts. Leave any field blank to skip that test. Figures are for lead-acid batteries at about 25 °C; for 24 V systems the limits are doubled.

A flat battery is a symptom, not a diagnosis. Batteries are often replaced when the real fault is an alternator that isn't charging or a drain that empties the battery overnight. These four readings separate the likely causes in a few minutes, with any digital multimeter.

How to take the four readings

  1. Resting voltage. Leave the car switched off for at least two hours (overnight is best) so surface charge disappears. Set the multimeter to DC volts (20 V range), red probe on the positive post, black on the negative.
  2. Cranking voltage. Keep the probes on the posts while someone cranks the engine for a few seconds. Note the lowest reading. Disable the fuel pump fuse if you want to crank without starting.
  3. Charging voltage. Start the engine and hold it at about 2 000 rpm with everything electrical switched off.
  4. Charging under load. Still at about 2 000 rpm, switch on the headlights on high beam, the blower fan on full and the rear demister.

Measure on the battery posts, not the cable clamps. If the voltage on the clamps is lower than on the posts, the terminals are dirty or loose.

Battery voltage chart (12 V lead-acid, rested)

State of chargeStandard / EFBAGM
100%12.65 V and above12.85 V and above
75%12.45 V12.60 V
50%12.24 V12.40 V
25%12.06 V12.20 V
Flat11.9 V and below12.0 V and below

Lithium (LiFePO4) batteries hold an almost flat 13.2–13.4 V for most of their charge, so voltage is a poor guide to their state of charge. Use the battery's own monitor.

Smart-charging alternators

Many vehicles from about 2015, including popular bakkies and start-stop cars, use a smart-charging alternator controlled by the engine computer. The charging voltage can swing between about 12.5 V and 15 V depending on battery state and engine load, so a single low reading isn't proof of a fault. Test with loads switched on: the voltage should rise to support them. These systems usually have a battery sensor on the negative terminal and need the battery registered to the car after replacement. If you run a fridge or second battery off a smart alternator, use a DC-DC charger (see the Dual Battery and Fridge Battery Calculator).

From a reading to a quote

These tools help you understand the problem and ask the right questions, but they don't replace a proper test. An auto electrician checks the vehicle with the right equipment and confirms the cause before replacing parts. When you are ready, send what you found in the quote form, with Alternator Repairs already selected, and an auto electrician or supplier in your area will contact you with a price.

Frequently asked questions

What voltage should a car battery be?
A fully charged 12 V lead-acid battery that has rested for a few hours reads about 12.6 V (12.8 V for AGM). With the engine running, a healthy charging system shows about 13.8–14.7 V at the battery.
What voltage is too low to start a car?
A rested battery below about 12.2 V is at half charge or less and may struggle on a cold morning. During cranking the voltage should stay above about 9.6 V; below that the starter slows down and the electronics can reset.
Can a battery read 12.6 V and still be bad?
Yes. Voltage shows charge, not capacity. A battery with sulphated or damaged plates can read a normal voltage but collapse under the starter's load. That is why the cranking test matters, and why an auto electrician uses a load or conductance tester.
How do I know if it's the battery or the alternator?
If the battery is charged and the running voltage stays below about 13.2 V, the alternator (or its belt or wiring) isn't charging. If the charging voltage is normal but the battery goes flat or drops below 9.6 V while cranking, the battery is the likely problem.

More auto electrical tools

Get a free quote