Get a quote

12V / 24V Wire Size and Voltage Drop Calculator

Low-voltage circuits lose a surprising amount of voltage in cable that is too thin: dim spotlights, a fridge that cuts out and a second battery that never charges fully. Enter the load and the run length to get the cable size that keeps the drop in check.

AE-mm²Auto-range · 12/24 V
Cable size–
Current
–
Minimum size
–
Voltage drop
–
Voltage at the load
–
Nearest AWG
–
Cable rating
–
CableDropAt loadRated

Copper cable at about 25 °C (0.0175 Ω·mm²/m). Current ratings are conservative figures for a single PVC auto cable in free air; derate by about 30% in a bundled loom or a hot engine bay.

In a 12 V system a 1 V drop is more than 8% of the supply, so cable sizing is about voltage drop as much as current rating. A 25 A fridge or light-bar circuit run to the back of a bakkie through 1.5 mm² cable can lose 2 V before it reaches the load. This calculator picks the smallest standard auto cable that meets both the voltage drop you choose and the current the load draws.

How the cable size is worked out

Voltage drop = current × resistance. Resistance depends on the total length of copper the current flows through and its cross-section: about 0.0175 Ω per metre for a 1 mm² copper conductor. With an earth wire back to the battery the current flows out and back, so the calculator doubles the length. With a chassis earth near the load only the positive cable counts, assuming a clean, solid earth.

It then checks the cable's current rating. Short runs at high current (a winch or inverter cable) are limited by heating; long runs at modest current (lights at the back of a trailer) are limited by voltage drop.

Auto cable sizes and typical uses

CableApprox. ratingTypical use
0.5–1 mm²7–11 ARelay triggers, switch feeds, LED marker lights, signal wires
1.5–2.5 mm²15–21 AHeadlights, horns, radio feeds, short spotlight runs
4–6 mm²28–37 ALight bars, fridges and 12 V sockets at the back of a bakkie, trailer plugs
10–16 mm²52–70 ADual battery links with a DC-DC charger, long fridge runs, small inverters
25–35 mm²95–120 ADual battery links without a charger, alternator upgrades, 1 000 W inverters
50–95 mm²150–230 AStarter and battery cables, winches, large inverters

Ratings drop in a bundled loom and in the engine bay, so go up a size there. For fusing, see the Fuse and Relay Size Calculator.

When to call an auto electrician

Wiring that is too thin gets hot, melts its insulation and can cause a fire, especially unfused cables near the battery. If you are adding spotlights or a light bar, a fridge socket or a dual battery system, an auto electrician will size, fuse and route the cable properly, use the correct crimps and heat-shrink, and keep it clear of the exhaust and moving parts.

From a reading to a quote

These tools help you understand the problem and ask the right questions, but they don't replace a proper test. An auto electrician checks the vehicle with the right equipment and confirms the cause before replacing parts. When you are ready, send what you found in the quote form, with Car Wiring Repairs already selected, and an auto electrician or supplier in your area will contact you with a price.

Frequently asked questions

What size cable do I need for a 12 V fridge?
A compressor fridge draws about 4–6 A while running, but it is sensitive to low voltage and switches off at about 10.5–11.5 V. For a 3–5 m run to the back of a bakkie, 4 mm² or 6 mm² cable keeps the drop under 3%. Thin cigarette-lighter cables are often the reason fridges cut out.
What size cable do I need for a dual battery system?
With a 25 A DC-DC charger and a 3–4 m run from the start battery to the second battery, 10 mm² is usually enough; for a 40 A charger use 16 mm². A direct link through an isolator without a charger carries much more current and typically needs 25–35 mm².
Does a 24 V truck need thinner cable?
For the same power, a 24 V system draws half the current, and the allowed drop in volts is twice as large, so the cable can be roughly a quarter of the cross-section of a 12 V circuit for the same load and length.
What does mm² mean on auto cable?
It is the cross-sectional area of the copper conductor, not the outside diameter of the cable. Some cheap cable is sold by its outside size or has thick insulation over a thin core, so check the copper area on the packaging or the supplier's specification.

More auto electrical tools

Get a free quote