Get a quote

Fuse and Relay Size Calculator

Adding spotlights, a light bar, a compressor or a 12 V socket? Enter the wattage and how many there are. The meter shows the current, the fuse rating and blade colour, the minimum cable and whether you need a relay.

AE-AAuto-range · 12/24 V
Fuse rating–
Circuit current
–
Fuse rating
–
Blade colour
–
Fuse type
–
Minimum cable
–
Relay
–

The fuse protects the cable, so the cable must be rated for at least the fuse. Colours are the standard ATO / mini blade fuse colours; maxi fuses use a different colour code.

A fuse exists to protect the wire, not the accessory. It must blow before the cable overheats, but not during the normal surge when a light or motor switches on. The usual rule is to fuse 25% above the continuous current for lights and electronics, and about 50% above it for motors and compressors, which draw a large inrush current at start-up.

Watts to amps

Current (A) = power (W) ÷ voltage (V). A 60 W spotlight on a 12 V system draws 5 A; two of them draw 10 A. Use the system's nominal voltage (12 V or 24 V) for sizing. The same light on a 24 V truck draws half the current.

Blade fuse colour chart

RatingColourRatingColour
1 ABlack10 ARed
2 AGrey15 ABlue
3 AViolet20 AYellow
4 APink25 AClear / white
5 ATan30 AGreen
7.5 ABrown35 ABlue-green
40 AOrange

These colours apply to standard (ATO), mini and low-profile mini blade fuses. Maxi fuses (20–120 A) use a different code, so always read the number on the fuse.

When you need a relay

Most dashboard switches are rated for 5–10 A, and long thin switch wires waste voltage. A relay lets the switch carry only the coil current (about 0.15 A) while heavy cable takes the load current straight from a fused battery feed. Use a relay for spotlights, light bars, air horns, compressors and anything over about 5 A. For high beam-triggered spotlights, the relay coil is wired to the high beam feed. If you would rather have it done properly, an auto electrician can wire spotlights and light bars or trace a fuse that keeps blowing.

From a reading to a quote

These tools help you understand the problem and ask the right questions, but they don't replace a proper test. An auto electrician checks the vehicle with the right equipment and confirms the cause before replacing parts. When you are ready, send what you found in the quote form, with Car Wiring Repairs already selected, and an auto electrician or supplier in your area will contact you with a price.

Frequently asked questions

Can I put a bigger fuse in if one keeps blowing?
No. A fuse that keeps blowing is doing its job: there is a short circuit, a chafed wire or a circuit carrying more than it was designed for. A bigger fuse lets the wire overheat instead, which can melt the loom or start a fire. Find the cause first.
What fuse do I need for a 12 V fridge?
Most 12 V compressor fridges draw 4–6 A running, with a short start-up surge. A 10 A or 15 A fuse is typical; check the fridge manual, as many specify the fuse rating. The cable must be rated for at least the fuse.
Where should the fuse go?
As close to the power source as possible, ideally within 300 mm of the battery terminal. The fuse protects everything downstream of it, so a fuse at the accessory end leaves the whole cable run unprotected.
What is the difference between a blade fuse and a MIDI or ANL fuse?
Blade fuses cover 1–40 A circuits and plug into a fuse box or holder. MIDI, ANL and MEGA fuses bolt in and cover 30–300 A or more, for dual battery links, inverters, winches and alternator cables.

More auto electrical tools

Get a free quote